產品標準 Standard

　　本產品按GB12706-91《額定電壓35KV及以下銅芯、鋁芯塑料絕緣電力電纜》、GB12666.5-90《電線電纜成束燃燒試驗》、GB/T17650-1998《取自電纜或光纜的材料燃燒時釋出氣體的試驗方法》和GB/T17651-1998《電纜或光纜在特定條件下燃燒的煙密度測定》標準生產0.6/1kv~26/35kv塑料絕緣電力電纜，同時還可根據用戶需要按國際電工委員會推薦標準IEC、英國標準、德國標準及美國標準生產。

The product is manufactured according to the standard of GB12706-91、GB12666.5-90、GB/T17650-1998 and GB/T17651-1998 or IEC and DIN and ICEA.

 

適用范圍 Applications

　　本產品適用于工頻額定電壓0.6/1kv~26/35KV 輸配電線路作配送電能之用。

The product is suitable for power transmission and distribution lines with rated voltage 0.6/1kv~26/35kv.

 

使用特性 Operating characteristics .

　　工頻額定電壓U0/U為0.6/1kv~26/35kv.

Rated power frequency voltage U0/U:0.6/1KV~26/35KV.

　　PVC絕緣電纜導體的長期最高工作溫度為70℃。XLPE絕緣電纜導體的長期允許最高工作溫度為90℃

PVC insulated power cable Max . permissible continuous operating temperature of the conductor should not exceed 70 ℃,XPLE permissible continuous operating temperature of the conductor should not exceed 90℃.

　　短路時（最長持續時間不超過5s）電纜導體的最高溫度不超過250

Max Short –circurrt temperature of conductor shall not exceed 250.(5s maximum duration)

　　電纜敷設時環境溫度不低于0℃

The installation temperature should not below 0℃

　　電纜阻燃性能滿足GB12666.5-90標準A類相應指標要求。

The flame-ratardant properties of cable comply with the requirements specified in A kind of GB12666.5-90

　　低鹵電纜除應滿足GB12666.5-90標準中A類相應指標要求外，還應滿足GB/T17650.1-1998標準規定的相應指標。

The flame-retardant properties of lower halogen cable comply with requirements specified in A kind of GB12666.5-90 except compluing with requirements specified in GB/T17650.2-1998 .

　　無鹵電纜除應滿足GB12666.5-90標準中A類相應指標要求外，還應滿足GB/T17650.2-1998和GB/T17651-1998標準規定的相應指標。

The flame-retardant properties of no halogen cable comply with requirements specified in A kind of GB12666.5-90 except compluing with requirements specified in GB/T17650.2-1998 .and GB/T17651-1998.

　　電纜彎曲半徑：三芯電纜不小于電纜外徑15倍；單芯電纜不小于電纜外徑20倍。

Three bending radius of a single core should not less than 20 times of the cable diameter

Two bending radius of a three-core cable should not less than 15 times of the cable diameter.

電纜額定電壓的選擇 Voltage designation

　　電纜額定電壓應適合于電纜的系統的運行狀況，用U0/U（Um）表示，均為有效值，單位為kv

　　U0- 電纜設計用導體與屏蔽或金屬套之間的額定工作電壓；

　　U—電纜設計用導體之間的額定工頻電壓；

　　Um –設備可承受的“最高系統”電壓的最大值。

The rated voltage of the cable for a given application shall be suitable for the operating condition in the system in which the cable is used , and is expressed in the form of U0/U（Um）are applied to the system voltages and running state , and expressed in the form U0/Ukv.

U0-The rated power-frequency voltage between conductor and earth or metallic screen ,for which the cable designed .

U-The rated power –frequency voltage between conductors for which the cable designed.

Um- –The maximum value of “the highest system voltage ”for which the equipment may be used.

三相系統用電纜的U0值推薦如下表：

The values U0 recommended for cables to be used in three-phase systems are listed below:

 

 第一類——用于單相接地故障時間每一次一般不大于1min，亦可用于最長不超過8小時，每年累計不超過125小時的系統。

第二類——用于接地故障時間更長的系統及對電纜絕緣性能要求較高的場合。

The first class cable – suitable for one single –phase earthing – block time does not exceed one minute each time. Max. time not exceed 8 hours ,and not exceed 125 hours in all in one year.

The second class cable – suitable for more the earthing – block time and more better insulated performa. 電纜的型號 Type of cable

 

0.6/1kv高阻燃（隔氧層）電纜的生產范圍

Production Range of high performance flame –retardant cable

---

上一篇： 耐火電纜介紹

下一篇： 電力電纜進水的危害、原因以及如何及時解決問題